WikiStart: PrusaSlicer_Anycubic_4Max_Pro_Bundle.ini

File PrusaSlicer_Anycubic_4Max_Pro_Bundle.ini, 28.7 KB (added by dsl, 5 months ago)
Line 
1# generated by PrusaSlicer 2.1.0+ on 2020-05-03 at 13:38:57 UTC
2
3[print:Anycubic Mega X]
4avoid_crossing_perimeters = 0
5bottom_fill_pattern = rectilinear
6bottom_solid_layers = 3
7bridge_acceleration = 0
8bridge_angle = 0
9bridge_flow_ratio = 1
10bridge_speed = 60
11brim_width = 0
12clip_multipart_objects = 0
13compatible_printers = 
14compatible_printers_condition = 
15complete_objects = 0
16default_acceleration = 0
17dont_support_bridges = 1
18elefant_foot_compensation = 0
19ensure_vertical_shell_thickness = 0
20external_perimeter_extrusion_width = 0.45
21external_perimeter_speed = 50%
22external_perimeters_first = 0
23extra_perimeters = 1
24extruder_clearance_height = 20
25extruder_clearance_radius = 20
26extrusion_width = 0.45
27fill_angle = 45
28fill_density = 20%
29fill_pattern = stars
30first_layer_acceleration = 0
31first_layer_extrusion_width = 0.42
32first_layer_height = 0.35
33first_layer_speed = 30
34gap_fill_speed = 20
35gcode_comments = 0
36gcode_label_objects = 0
37infill_acceleration = 0
38infill_every_layers = 1
39infill_extruder = 1
40infill_extrusion_width = 0.45
41infill_first = 0
42infill_only_where_needed = 0
43infill_overlap = 25%
44infill_speed = 80
45inherits = 
46interface_shells = 0
47layer_height = 0.3
48max_print_speed = 80
49max_volumetric_speed = 0
50min_skirt_length = 0
51notes = 
52only_retract_when_crossing_perimeters = 1
53ooze_prevention = 0
54output_filename_format = [input_filename_base].gcode
55overhangs = 1
56perimeter_acceleration = 0
57perimeter_extruder = 1
58perimeter_extrusion_width = 0.45
59perimeter_speed = 60
60perimeters = 3
61post_process = 
62print_settings_id = 
63raft_layers = 0
64resolution = 0
65seam_position = aligned
66single_extruder_multi_material_priming = 1
67skirt_distance = 6
68skirt_height = 1
69skirts = 1
70slice_closing_radius = 0.049
71small_perimeter_speed = 15
72solid_infill_below_area = 70
73solid_infill_every_layers = 0
74solid_infill_extruder = 1
75solid_infill_extrusion_width = 0.45
76solid_infill_speed = 20
77spiral_vase = 0
78standby_temperature_delta = -5
79support_material = 0
80support_material_angle = 0
81support_material_auto = 1
82support_material_buildplate_only = 0
83support_material_contact_distance = 0.2
84support_material_enforce_layers = 0
85support_material_extruder = 1
86support_material_extrusion_width = 0.35
87support_material_interface_contact_loops = 0
88support_material_interface_extruder = 1
89support_material_interface_layers = 3
90support_material_interface_spacing = 0
91support_material_interface_speed = 100%
92support_material_pattern = rectilinear
93support_material_spacing = 2.5
94support_material_speed = 60
95support_material_synchronize_layers = 0
96support_material_threshold = 0
97support_material_with_sheath = 1
98support_material_xy_spacing = 50%
99thin_walls = 1
100threads = 4
101top_fill_pattern = rectilinear
102top_infill_extrusion_width = 0.4
103top_solid_infill_speed = 15
104top_solid_layers = 3
105travel_speed = 130
106wipe_tower = 0
107wipe_tower_bridging = 10
108wipe_tower_rotation_angle = 0
109wipe_tower_width = 60
110wipe_tower_x = 180
111wipe_tower_y = 140
112xy_size_compensation = 0
113
114[print:Case_for_Xling]
115avoid_crossing_perimeters = 0
116bottom_fill_pattern = rectilinear
117bottom_solid_layers = 5
118bridge_acceleration = 0
119bridge_angle = 0
120bridge_flow_ratio = 1
121bridge_speed = 60
122brim_width = 0
123clip_multipart_objects = 0
124compatible_printers = 
125compatible_printers_condition = 
126complete_objects = 0
127default_acceleration = 0
128dont_support_bridges = 1
129elefant_foot_compensation = 0
130ensure_vertical_shell_thickness = 0
131external_perimeter_extrusion_width = 0.4
132external_perimeter_speed = 50%
133external_perimeters_first = 0
134extra_perimeters = 1
135extruder_clearance_height = 20
136extruder_clearance_radius = 20
137extrusion_width = 0.4
138fill_angle = 45
139fill_density = 10%
140fill_pattern = gyroid
141first_layer_acceleration = 0
142first_layer_extrusion_width = 0.4
143first_layer_height = 0.2
144first_layer_speed = 30
145gap_fill_speed = 20
146gcode_comments = 0
147gcode_label_objects = 0
148infill_acceleration = 0
149infill_every_layers = 1
150infill_extruder = 1
151infill_extrusion_width = 0.4
152infill_first = 0
153infill_only_where_needed = 0
154infill_overlap = 25%
155infill_speed = 80
156inherits = 
157interface_shells = 0
158layer_height = 0.15
159max_print_speed = 80
160max_volumetric_speed = 0
161min_skirt_length = 0
162notes = 
163only_retract_when_crossing_perimeters = 0
164ooze_prevention = 0
165output_filename_format = [input_filename_base].gcode
166overhangs = 1
167perimeter_acceleration = 0
168perimeter_extruder = 1
169perimeter_extrusion_width = 0.4
170perimeter_speed = 60
171perimeters = 4
172post_process = 
173print_settings_id = 
174raft_layers = 0
175resolution = 0
176seam_position = aligned
177single_extruder_multi_material_priming = 1
178skirt_distance = 6
179skirt_height = 1
180skirts = 10
181slice_closing_radius = 0.049
182small_perimeter_speed = 15
183solid_infill_below_area = 70
184solid_infill_every_layers = 0
185solid_infill_extruder = 1
186solid_infill_extrusion_width = 0.4
187solid_infill_speed = 20
188spiral_vase = 0
189standby_temperature_delta = -5
190support_material = 1
191support_material_angle = 0
192support_material_auto = 0
193support_material_buildplate_only = 0
194support_material_contact_distance = 0.2
195support_material_enforce_layers = 0
196support_material_extruder = 1
197support_material_extrusion_width = 0.35
198support_material_interface_contact_loops = 1
199support_material_interface_extruder = 1
200support_material_interface_layers = 3
201support_material_interface_spacing = 0
202support_material_interface_speed = 80%
203support_material_pattern = rectilinear
204support_material_spacing = 2.5
205support_material_speed = 80
206support_material_synchronize_layers = 0
207support_material_threshold = 30
208support_material_with_sheath = 1
209support_material_xy_spacing = 25%
210thin_walls = 1
211threads = 4
212top_fill_pattern = rectilinear
213top_infill_extrusion_width = 0.4
214top_solid_infill_speed = 15
215top_solid_layers = 5
216travel_speed = 130
217wipe_tower = 0
218wipe_tower_bridging = 10
219wipe_tower_rotation_angle = 0
220wipe_tower_width = 60
221wipe_tower_x = 180
222wipe_tower_y = 140
223xy_size_compensation = 0
224
225[print:RC3_covid19_headband]
226avoid_crossing_perimeters = 0
227bottom_fill_pattern = rectilinear
228bottom_solid_layers = 3
229bridge_acceleration = 0
230bridge_angle = 0
231bridge_flow_ratio = 1
232bridge_speed = 70
233brim_width = 6
234clip_multipart_objects = 0
235compatible_printers = 
236compatible_printers_condition = 
237complete_objects = 0
238default_acceleration = 0
239dont_support_bridges = 1
240elefant_foot_compensation = 0
241ensure_vertical_shell_thickness = 0
242external_perimeter_extrusion_width = 0.4
243external_perimeter_speed = 70%
244external_perimeters_first = 0
245extra_perimeters = 1
246extruder_clearance_height = 20
247extruder_clearance_radius = 20
248extrusion_width = 0.4
249fill_angle = 45
250fill_density = 20%
251fill_pattern = honeycomb
252first_layer_acceleration = 0
253first_layer_extrusion_width = 0.4
254first_layer_height = 0.2
255first_layer_speed = 70
256gap_fill_speed = 20
257gcode_comments = 0
258gcode_label_objects = 0
259infill_acceleration = 0
260infill_every_layers = 1
261infill_extruder = 1
262infill_extrusion_width = 0.4
263infill_first = 0
264infill_only_where_needed = 0
265infill_overlap = 25%
266infill_speed = 70
267inherits = 
268interface_shells = 0
269layer_height = 0.25
270max_print_speed = 80
271max_volumetric_speed = 0
272min_skirt_length = 0
273notes = 
274only_retract_when_crossing_perimeters = 0
275ooze_prevention = 0
276output_filename_format = [input_filename_base].gcode
277overhangs = 1
278perimeter_acceleration = 0
279perimeter_extruder = 1
280perimeter_extrusion_width = 0.4
281perimeter_speed = 70
282perimeters = 3
283post_process = 
284print_settings_id = 
285raft_layers = 0
286resolution = 0
287seam_position = aligned
288single_extruder_multi_material_priming = 1
289skirt_distance = 3
290skirt_height = 1
291skirts = 0
292slice_closing_radius = 0.049
293small_perimeter_speed = 15
294solid_infill_below_area = 70
295solid_infill_every_layers = 0
296solid_infill_extruder = 1
297solid_infill_extrusion_width = 0.4
298solid_infill_speed = 35
299spiral_vase = 0
300standby_temperature_delta = -5
301support_material = 0
302support_material_angle = 0
303support_material_auto = 1
304support_material_buildplate_only = 1
305support_material_contact_distance = 0.2
306support_material_enforce_layers = 0
307support_material_extruder = 1
308support_material_extrusion_width = 0.35
309support_material_interface_contact_loops = 0
310support_material_interface_extruder = 1
311support_material_interface_layers = 3
312support_material_interface_spacing = 0
313support_material_interface_speed = 100%
314support_material_pattern = rectilinear
315support_material_spacing = 2.5
316support_material_speed = 70
317support_material_synchronize_layers = 0
318support_material_threshold = 30
319support_material_with_sheath = 1
320support_material_xy_spacing = 25%
321thin_walls = 1
322threads = 4
323top_fill_pattern = rectilinear
324top_infill_extrusion_width = 0.4
325top_solid_infill_speed = 15
326top_solid_layers = 3
327travel_speed = 70
328wipe_tower = 0
329wipe_tower_bridging = 10
330wipe_tower_rotation_angle = 0
331wipe_tower_width = 60
332wipe_tower_x = 180
333wipe_tower_y = 140
334xy_size_compensation = 0
335
336[print:RC3_covid19_klamer]
337avoid_crossing_perimeters = 0
338bottom_fill_pattern = rectilinear
339bottom_solid_layers = 3
340bridge_acceleration = 0
341bridge_angle = 0
342bridge_flow_ratio = 1
343bridge_speed = 50
344brim_width = 0
345clip_multipart_objects = 0
346compatible_printers = 
347compatible_printers_condition = 
348complete_objects = 0
349default_acceleration = 0
350dont_support_bridges = 1
351elefant_foot_compensation = 0
352ensure_vertical_shell_thickness = 0
353external_perimeter_extrusion_width = 0.4
354external_perimeter_speed = 70%
355external_perimeters_first = 0
356extra_perimeters = 1
357extruder_clearance_height = 20
358extruder_clearance_radius = 20
359extrusion_width = 0.4
360fill_angle = 45
361fill_density = 100%
362fill_pattern = rectilinear
363first_layer_acceleration = 0
364first_layer_extrusion_width = 0.4
365first_layer_height = 0.2
366first_layer_speed = 50
367gap_fill_speed = 20
368gcode_comments = 0
369gcode_label_objects = 0
370infill_acceleration = 0
371infill_every_layers = 1
372infill_extruder = 1
373infill_extrusion_width = 0.4
374infill_first = 0
375infill_only_where_needed = 0
376infill_overlap = 25%
377infill_speed = 50
378inherits = 
379interface_shells = 0
380layer_height = 0.25
381max_print_speed = 80
382max_volumetric_speed = 0
383min_skirt_length = 0
384notes = 
385only_retract_when_crossing_perimeters = 0
386ooze_prevention = 0
387output_filename_format = [input_filename_base].gcode
388overhangs = 1
389perimeter_acceleration = 0
390perimeter_extruder = 1
391perimeter_extrusion_width = 0.4
392perimeter_speed = 50
393perimeters = 3
394post_process = 
395print_settings_id = 
396raft_layers = 0
397resolution = 0
398seam_position = aligned
399single_extruder_multi_material_priming = 1
400skirt_distance = 3
401skirt_height = 1
402skirts = 6
403slice_closing_radius = 0.049
404small_perimeter_speed = 15
405solid_infill_below_area = 70
406solid_infill_every_layers = 0
407solid_infill_extruder = 1
408solid_infill_extrusion_width = 0.4
409solid_infill_speed = 35
410spiral_vase = 0
411standby_temperature_delta = -5
412support_material = 0
413support_material_angle = 0
414support_material_auto = 1
415support_material_buildplate_only = 1
416support_material_contact_distance = 0.2
417support_material_enforce_layers = 0
418support_material_extruder = 1
419support_material_extrusion_width = 0.35
420support_material_interface_contact_loops = 0
421support_material_interface_extruder = 1
422support_material_interface_layers = 3
423support_material_interface_spacing = 0
424support_material_interface_speed = 100%
425support_material_pattern = rectilinear
426support_material_spacing = 2.5
427support_material_speed = 50
428support_material_synchronize_layers = 0
429support_material_threshold = 30
430support_material_with_sheath = 1
431support_material_xy_spacing = 25%
432thin_walls = 1
433threads = 4
434top_fill_pattern = rectilinear
435top_infill_extrusion_width = 0.4
436top_solid_infill_speed = 15
437top_solid_layers = 3
438travel_speed = 50
439wipe_tower = 0
440wipe_tower_bridging = 10
441wipe_tower_rotation_angle = 0
442wipe_tower_width = 60
443wipe_tower_x = 180
444wipe_tower_y = 140
445xy_size_compensation = 0
446
447[print:model_sup]
448avoid_crossing_perimeters = 1
449bottom_fill_pattern = rectilinear
450bottom_solid_layers = 3
451bridge_acceleration = 0
452bridge_angle = 0
453bridge_flow_ratio = 1
454bridge_speed = 80
455brim_width = 0
456clip_multipart_objects = 0
457compatible_printers = 
458compatible_printers_condition = 
459complete_objects = 0
460default_acceleration = 0
461dont_support_bridges = 1
462elefant_foot_compensation = 0
463ensure_vertical_shell_thickness = 0
464external_perimeter_extrusion_width = 0.4
465external_perimeter_speed = 50%
466external_perimeters_first = 0
467extra_perimeters = 1
468extruder_clearance_height = 20
469extruder_clearance_radius = 20
470extrusion_width = 0.4
471fill_angle = 45
472fill_density = 100%
473fill_pattern = rectilinear
474first_layer_acceleration = 0
475first_layer_extrusion_width = 0.4
476first_layer_height = 0.2
477first_layer_speed = 50
478gap_fill_speed = 20
479gcode_comments = 0
480gcode_label_objects = 0
481infill_acceleration = 0
482infill_every_layers = 1
483infill_extruder = 1
484infill_extrusion_width = 0.4
485infill_first = 0
486infill_only_where_needed = 0
487infill_overlap = 25%
488infill_speed = 80
489inherits = 
490interface_shells = 0
491layer_height = 0.15
492max_print_speed = 80
493max_volumetric_speed = 0
494min_skirt_length = 0
495notes = 
496only_retract_when_crossing_perimeters = 0
497ooze_prevention = 0
498output_filename_format = [input_filename_base].gcode
499overhangs = 1
500perimeter_acceleration = 0
501perimeter_extruder = 1
502perimeter_extrusion_width = 0.4
503perimeter_speed = 80
504perimeters = 3
505post_process = 
506print_settings_id = 
507raft_layers = 0
508resolution = 0
509seam_position = aligned
510single_extruder_multi_material_priming = 1
511skirt_distance = 3
512skirt_height = 1
513skirts = 8
514slice_closing_radius = 0.049
515small_perimeter_speed = 15
516solid_infill_below_area = 70
517solid_infill_every_layers = 0
518solid_infill_extruder = 1
519solid_infill_extrusion_width = 0.4
520solid_infill_speed = 20
521spiral_vase = 0
522standby_temperature_delta = -5
523support_material = 0
524support_material_angle = 0
525support_material_auto = 1
526support_material_buildplate_only = 1
527support_material_contact_distance = 0.2
528support_material_enforce_layers = 0
529support_material_extruder = 1
530support_material_extrusion_width = 0.35
531support_material_interface_contact_loops = 0
532support_material_interface_extruder = 1
533support_material_interface_layers = 3
534support_material_interface_spacing = 0
535support_material_interface_speed = 100%
536support_material_pattern = rectilinear
537support_material_spacing = 2.5
538support_material_speed = 80
539support_material_synchronize_layers = 0
540support_material_threshold = 30
541support_material_with_sheath = 1
542support_material_xy_spacing = 25%
543thin_walls = 1
544threads = 4
545top_fill_pattern = rectilinear
546top_infill_extrusion_width = 0.4
547top_solid_infill_speed = 15
548top_solid_layers = 3
549travel_speed = 130
550wipe_tower = 0
551wipe_tower_bridging = 10
552wipe_tower_rotation_angle = 0
553wipe_tower_width = 60
554wipe_tower_x = 180
555wipe_tower_y = 140
556xy_size_compensation = 0
557
558[filament:Anycubic Mega X]
559bed_temperature = 0
560bridge_fan_speed = 100
561compatible_printers = 
562compatible_printers_condition = 
563compatible_prints = 
564compatible_prints_condition = 
565cooling = 1
566disable_fan_first_layers = 3
567end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
568extrusion_multiplier = 1
569fan_always_on = 0
570fan_below_layer_time = 60
571filament_colour = #29B2B2
572filament_cooling_final_speed = 3.4
573filament_cooling_initial_speed = 2.2
574filament_cooling_moves = 4
575filament_cost = 0
576filament_density = 0
577filament_deretract_speed = nil
578filament_diameter = 1.75
579filament_load_time = 0
580filament_loading_speed = 28
581filament_loading_speed_start = 3
582filament_max_volumetric_speed = 0
583filament_minimal_purge_on_wipe_tower = 15
584filament_notes = ""
585filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
586filament_retract_before_travel = nil
587filament_retract_before_wipe = nil
588filament_retract_layer_change = nil
589filament_retract_length = nil
590filament_retract_lift = nil
591filament_retract_lift_above = nil
592filament_retract_lift_below = nil
593filament_retract_restart_extra = nil
594filament_retract_speed = nil
595filament_settings_id = ""
596filament_soluble = 0
597filament_toolchange_delay = 0
598filament_type = PLA
599filament_unload_time = 0
600filament_unloading_speed = 90
601filament_unloading_speed_start = 100
602filament_wipe = nil
603first_layer_bed_temperature = 0
604first_layer_temperature = 200
605inherits = 
606max_fan_speed = 100
607min_fan_speed = 35
608min_print_speed = 10
609slowdown_below_layer_time = 5
610start_filament_gcode = "; Filament gcode\n"
611temperature = 200
612
613[filament:Anycubic_4max_pro]
614bed_temperature = 60
615bridge_fan_speed = 100
616compatible_printers = 
617compatible_printers_condition = 
618compatible_prints = 
619compatible_prints_condition = 
620cooling = 1
621disable_fan_first_layers = 3
622end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
623extrusion_multiplier = 1
624fan_always_on = 0
625fan_below_layer_time = 60
626filament_colour = #29B2B2
627filament_cooling_final_speed = 3.4
628filament_cooling_initial_speed = 2.2
629filament_cooling_moves = 4
630filament_cost = 0
631filament_density = 0
632filament_deretract_speed = nil
633filament_diameter = 1.75
634filament_load_time = 0
635filament_loading_speed = 28
636filament_loading_speed_start = 3
637filament_max_volumetric_speed = 0
638filament_minimal_purge_on_wipe_tower = 15
639filament_notes = ""
640filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
641filament_retract_before_travel = nil
642filament_retract_before_wipe = nil
643filament_retract_layer_change = nil
644filament_retract_length = nil
645filament_retract_lift = nil
646filament_retract_lift_above = nil
647filament_retract_lift_below = nil
648filament_retract_restart_extra = nil
649filament_retract_speed = nil
650filament_settings_id = ""
651filament_soluble = 0
652filament_toolchange_delay = 0
653filament_type = PLA
654filament_unload_time = 0
655filament_unloading_speed = 90
656filament_unloading_speed_start = 100
657filament_wipe = nil
658first_layer_bed_temperature = 60
659first_layer_temperature = 205
660inherits = 
661max_fan_speed = 100
662min_fan_speed = 35
663min_print_speed = 10
664slowdown_below_layer_time = 5
665start_filament_gcode = "; Filament gcode\n"
666temperature = 205
667
668[filament:Devil Design PLA]
669bed_temperature = 55
670bridge_fan_speed = 75
671compatible_printers = 
672compatible_printers_condition = ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
673compatible_prints = 
674compatible_prints_condition = 
675cooling = 1
676disable_fan_first_layers = 3
677end_filament_gcode = "; Filament-specific end gcode"
678extrusion_multiplier = 1
679fan_always_on = 1
680fan_below_layer_time = 100
681filament_colour = #FF3232
682filament_cooling_final_speed = 3.4
683filament_cooling_initial_speed = 2.2
684filament_cooling_moves = 4
685filament_cost = 25.4
686filament_density = 1.24
687filament_deretract_speed = nil
688filament_diameter = 1.75
689filament_load_time = 0
690filament_loading_speed = 28
691filament_loading_speed_start = 3
692filament_max_volumetric_speed = 15
693filament_minimal_purge_on_wipe_tower = 15
694filament_notes = "List of materials tested with standard PLA print settings:\n\nDas Filament\nEsun PLA\nEUMAKERS PLA\nFiberlogy HD-PLA\nFillamentum PLA\nFloreon3D\nHatchbox PLA\nPlasty Mladec PLA\nPrimavalue PLA\nProto pasta Matte Fiber\nVerbatim PLA\nVerbatim BVOH"
695filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
696filament_retract_before_travel = nil
697filament_retract_before_wipe = nil
698filament_retract_layer_change = nil
699filament_retract_length = 2
700filament_retract_lift = nil
701filament_retract_lift_above = nil
702filament_retract_lift_below = nil
703filament_retract_restart_extra = nil
704filament_retract_speed = nil
705filament_settings_id = ""
706filament_soluble = 0
707filament_toolchange_delay = 0
708filament_type = PLA
709filament_unload_time = 0
710filament_unloading_speed = 90
711filament_unloading_speed_start = 100
712filament_wipe = nil
713first_layer_bed_temperature = 60
714first_layer_temperature = 200
715inherits = Generic PLA
716max_fan_speed = 80
717min_fan_speed = 80
718min_print_speed = 15
719slowdown_below_layer_time = 20
720start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{elsif nozzle_diameter[0]==0.6}18{else}30{endif} ; Filament gcode"
721temperature = 195
722
723[filament:DevilDesign PETG]
724bed_temperature = 75
725bridge_fan_speed = 100
726compatible_printers = 
727compatible_printers_condition = nozzle_diameter[0]!=0.6 and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
728compatible_prints = 
729compatible_prints_condition = 
730cooling = 1
731disable_fan_first_layers = 3
732end_filament_gcode = "; Filament-specific end gcode"
733extrusion_multiplier = 1
734fan_always_on = 1
735fan_below_layer_time = 20
736filament_colour = #FF8000
737filament_cooling_final_speed = 3.4
738filament_cooling_initial_speed = 2.2
739filament_cooling_moves = 4
740filament_cost = 27.82
741filament_density = 1.27
742filament_deretract_speed = nil
743filament_diameter = 1.75
744filament_load_time = 0
745filament_loading_speed = 28
746filament_loading_speed_start = 3
747filament_max_volumetric_speed = 8
748filament_minimal_purge_on_wipe_tower = 15
749filament_notes = "List of manufacturers tested with standard PET print settings:\n\nE3D Edge\nPlasty Mladec PETG"
750filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
751filament_retract_before_travel = nil
752filament_retract_before_wipe = nil
753filament_retract_layer_change = nil
754filament_retract_length = 2
755filament_retract_lift = nil
756filament_retract_lift_above = nil
757filament_retract_lift_below = nil
758filament_retract_restart_extra = nil
759filament_retract_speed = nil
760filament_settings_id = ""
761filament_soluble = 0
762filament_toolchange_delay = 0
763filament_type = PET
764filament_unload_time = 0
765filament_unloading_speed = 90
766filament_unloading_speed_start = 100
767filament_wipe = nil
768first_layer_bed_temperature = 75
769first_layer_temperature = 230
770inherits = Prusa PET
771max_fan_speed = 100
772min_fan_speed = 100
773min_print_speed = 15
774slowdown_below_layer_time = 20
775start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{elsif nozzle_diameter[0]==0.6}24{else}45{endif} ; Filament gcode"
776temperature = 220
777
778[filament:Prusament PETG - for Xling case]
779bed_temperature = 90
780bridge_fan_speed = 50
781compatible_printers = 
782compatible_printers_condition = nozzle_diameter[0]!=0.6 and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
783compatible_prints = 
784compatible_prints_condition = 
785cooling = 1
786disable_fan_first_layers = 3
787end_filament_gcode = "; Filament-specific end gcode"
788extrusion_multiplier = 1
789fan_always_on = 1
790fan_below_layer_time = 20
791filament_colour = #FF8000
792filament_cooling_final_speed = 3.4
793filament_cooling_initial_speed = 2.2
794filament_cooling_moves = 4
795filament_cost = 24.99
796filament_density = 1.27
797filament_deretract_speed = nil
798filament_diameter = 1.75
799filament_load_time = 0
800filament_loading_speed = 28
801filament_loading_speed_start = 3
802filament_max_volumetric_speed = 8
803filament_minimal_purge_on_wipe_tower = 15
804filament_notes = ""
805filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
806filament_retract_before_travel = nil
807filament_retract_before_wipe = nil
808filament_retract_layer_change = nil
809filament_retract_length = nil
810filament_retract_lift = nil
811filament_retract_lift_above = nil
812filament_retract_lift_below = nil
813filament_retract_restart_extra = nil
814filament_retract_speed = nil
815filament_settings_id = ""
816filament_soluble = 0
817filament_toolchange_delay = 0
818filament_type = PETG
819filament_unload_time = 0
820filament_unloading_speed = 90
821filament_unloading_speed_start = 100
822filament_wipe = nil
823first_layer_bed_temperature = 85
824first_layer_temperature = 240
825inherits = Prusament PETG
826max_fan_speed = 50
827min_fan_speed = 30
828min_print_speed = 15
829slowdown_below_layer_time = 20
830start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{elsif nozzle_diameter[0]==0.6}24{else}45{endif} ; Filament gcode"
831temperature = 250
832
833[printer:Anycubic 4Max Pro]
834bed_custom_model = 
835bed_custom_texture = 
836bed_shape = 0x0,270x0,270x205,0x205
837before_layer_gcode = 
838between_objects_gcode = 
839cooling_tube_length = 5
840cooling_tube_retraction = 91.5
841default_filament_profile = ""
842default_print_profile = 
843deretract_speed = 0
844end_gcode = M104 S0 ; turn off extruder\nM140 S0 ; turn off bed\nM84 ; disable motors\nM107\nG91 ;relative positioning\nG1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure\nG1 Z+0.5 E-5 ;X-20 Y-20 F[travel_speed] ;move Z up a bit and retract filament even more\nG28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way\nM84 ;steppers off\nG90\nM300 P300 S4000
845extra_loading_move = -2
846extruder_colour = ""
847extruder_offset = 0x0
848gcode_flavor = marlin
849high_current_on_filament_swap = 0
850host_type = octoprint
851inherits = 
852layer_gcode = 
853machine_max_acceleration_e = 10000,5000
854machine_max_acceleration_extruding = 1500,1250
855machine_max_acceleration_retracting = 1500,1250
856machine_max_acceleration_x = 9000,1000
857machine_max_acceleration_y = 9000,1000
858machine_max_acceleration_z = 500,200
859machine_max_feedrate_e = 120,120
860machine_max_feedrate_x = 500,200
861machine_max_feedrate_y = 500,200
862machine_max_feedrate_z = 12,12
863machine_max_jerk_e = 2.5,2.5
864machine_max_jerk_x = 10,10
865machine_max_jerk_y = 10,10
866machine_max_jerk_z = 0.2,0.4
867machine_min_extruding_rate = 0,0
868machine_min_travel_rate = 0,0
869max_layer_height = 0
870max_print_height = 270
871min_layer_height = 0.07
872nozzle_diameter = 0.4
873parking_pos_retraction = 92
874print_host = 
875printer_model = 
876printer_notes = 
877printer_settings_id = 
878printer_technology = FFF
879printer_variant = 
880printer_vendor = 
881printhost_apikey = 
882printhost_cafile = 
883remaining_times = 0
884retract_before_travel = 2
885retract_before_wipe = 0%
886retract_layer_change = 0
887retract_length = 2
888retract_length_toolchange = 10
889retract_lift = 0
890retract_lift_above = 0
891retract_lift_below = 0
892retract_restart_extra = 0
893retract_restart_extra_toolchange = 0
894retract_speed = 40
895serial_port = 
896serial_speed = 250000
897silent_mode = 1
898single_extruder_multi_material = 0
899start_gcode = G21 ;metric values\nG90 ;absolute positioning\nM82 ;set extruder to absolute mode\nM107 ;start with the fan off\nG28 X0 Y0 ;move X/Y to min endstops\nG28 Z0 ;move Z to min endstops\nG1 Z15.0 F[travel_speed] ;move the platform down 15mm\nG92 E0 ;zero the extruded length\nG1 F200 E3 ;extrude 3mm of feed stock\nG92 E0 ;zero the extruded length again\nG1 F[travel_speed]\nM117 Printing...\nG5
900toolchange_gcode = 
901use_firmware_retraction = 0
902use_relative_e_distances = 0
903use_volumetric_e = 0
904variable_layer_height = 1
905wipe = 0
906z_offset = 0
907
908[printer:Anycubic Mega X]
909bed_custom_model = 
910bed_custom_texture = 
911bed_shape = 0x0,300x0,300x300,0x300
912before_layer_gcode = 
913between_objects_gcode = 
914cooling_tube_length = 5
915cooling_tube_retraction = 91.5
916default_filament_profile = ""
917default_print_profile = 
918deretract_speed = 0
919end_gcode = M104 S0 ; turn off extruder\nM140 S0 ; turn off bed\nM84 ; disable motors\nM107\nG91 ;relative positioning\nG1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure\nG1 Z+0.5 E-5 ;X-20 Y-20 F[travel_speed] ;move Z up a bit and retract filament even more\nG28 X0 ;Y0 ;move X/Y to min endstops, so the head is out of the way\nG1 Y180 F2000\nM84 ;steppers off\nG90\nM300 P300 S4000
920extra_loading_move = -2
921extruder_colour = ""
922extruder_offset = 0x0
923gcode_flavor = marlin
924high_current_on_filament_swap = 0
925host_type = octoprint
926inherits = 
927layer_gcode = 
928machine_max_acceleration_e = 10000,5000
929machine_max_acceleration_extruding = 1500,1250
930machine_max_acceleration_retracting = 1500,1250
931machine_max_acceleration_x = 9000,1000
932machine_max_acceleration_y = 9000,1000
933machine_max_acceleration_z = 500,200
934machine_max_feedrate_e = 120,120
935machine_max_feedrate_x = 500,200
936machine_max_feedrate_y = 500,200
937machine_max_feedrate_z = 12,12
938machine_max_jerk_e = 2.5,2.5
939machine_max_jerk_x = 10,10
940machine_max_jerk_y = 10,10
941machine_max_jerk_z = 0.2,0.4
942machine_min_extruding_rate = 0,0
943machine_min_travel_rate = 0,0
944max_layer_height = 0
945max_print_height = 305
946min_layer_height = 0.07
947nozzle_diameter = 0.4
948parking_pos_retraction = 92
949print_host = 
950printer_model = 
951printer_notes = 
952printer_settings_id = 
953printer_technology = FFF
954printer_variant = 
955printer_vendor = 
956printhost_apikey = 
957printhost_cafile = 
958remaining_times = 0
959retract_before_travel = 2
960retract_before_wipe = 0%
961retract_layer_change = 0
962retract_length = 2
963retract_length_toolchange = 10
964retract_lift = 0
965retract_lift_above = 0
966retract_lift_below = 0
967retract_restart_extra = 0
968retract_restart_extra_toolchange = 0
969retract_speed = 40
970serial_port = 
971serial_speed = 250000
972silent_mode = 1
973single_extruder_multi_material = 0
974start_gcode = G21 ;metric values\nG90 ;absolute positioning\nM82 ;set extruder to absolute mode\nM107 ;start with the fan off\nG28 X0 Y0 ;move X/Y to min endstops\nG28 Z0 ;move Z to min endstops\nG1 Z15.0 F[travel_speed] ;move the platform down 15mm\nG92 E0 ;zero the extruded length\nG1 F200 E3 ;extrude 3mm of feed stock\nG92 E0 ;zero the extruded length again\nG1 F[travel_speed]\nG0 Y20 F[travel_speed]\nM117 Printing...\nG5
975toolchange_gcode = 
976use_firmware_retraction = 0
977use_relative_e_distances = 0
978use_volumetric_e = 0
979variable_layer_height = 1
980wipe = 0
981z_offset = 0
982
983[presets]
984print = Case_for_Xling
985sla_print = 0.05 Normal
986sla_material = Prusa Orange Tough 0.05
987printer = Anycubic 4Max Pro
988filament = DevilDesign PETG